Droplet based microfluidics
Direct-ink-writing (DIW) is a method of additive manufacturing whereby fluid material, referred to as ink, is extruded through a syringe and nozzle onto a substrate to build a part later-by-layer (Ink Printing). DIW is proving to be an emergent technology with applications in:
There are two most common base modalities to produce a back force to move the piston head which pushes ink through the syringe and nozzle:
Both have their drawbacks in terms of performance, especially when printing with compressible inks. Indeed, compressible inks change in volume when a pressure is applied to them in a closed space (such as the syringe), which means some of the energy applied by the piston is lost to compressing instead of extruding the ink. Pressure-based printing requires in-depth optimization prior to printing to determine the rheological complexities and pressure-to-flow rate relationship of each ink, and velocity-driven printing harbors very slow response to ink transients which makes printing with micro-nozzles impractical on a reasonable timescale.
Iterative learning techniques have become prevalent in recent years, and here [2] we apply this principle to DIW to effectively combine pressure-based and velocity-based printing to more accurately control ink volume flow rate and therefore final printed part shape fidelity.
This can be performed with automatic settling-detection of transients and material model generation followed by model updates during extrusion via a closed-loop control method involving velocity feedback from the motor controller and pressure feedback from the Elveflow sensor.
A foundational component to the operation of the flow control setup is a nested control loop.
Flow rate is considered to be known only when both the velocity of the piston that is pushing the ink and the pressure read by the sensor at the nozzle entrance are in a steady state. Because of this, model generation and flow control are possible through an automatic settling-detection algorithm which takes a moving average of the piston velocity and pressure to determine when the system is at steady state.
Model generation is done by prescribing three set pressures to the system. The corresponding flow rates to those pressures are then automatically found by the settling detection algorithm.
This sequence yields a rough material model consisting of three data points in the form of:
P(Q) = bQn
where P is pressure, Q is volume flow rate, and b and n are Power Law Model fit parameters. The three-point model is sent to the main controller and flow rate control iterations can begin.
NB : P_target corresponds to the desired pressure, and the graph represents the read pressure as the piston in the syringe compresses and extrudes the ink.If there is some error between the calculated flow rate at that pressure and the desired flow rate, then a change in pressure based on how much the flow rate needs to change to correct that error is calculated from the derivative of the material model equation, so the new P_target would be P_target_old + dP/dQ.
To control flow rate, the pressure for a desired flow rate is calculated from the Material Model and then the piston accelerates until the desired pressure is met. This pressure is then held constant, and the settling-detection will determine when the piston velocity is at steady-state and then report the volume flow rate. A flow rate error is then calculated, and from that error a new target pressure is calculated using P(Q) + dP/dQ, where dP/dQ is the derivative of the material model. In this way, the target pressure is constantly being updated based on the error between the read and the desired flow rate. The loop then begins again, iterating for pressure values and reporting the associated flow rate until a pressure which yields the target flow rate within an acceptable range is found.
This continues indefinitely and can then overcome the time-dependent properties of certain materials. Thixotropic materials, for example, become less viscous over time at a constant shear rate, and therefore have a changing pressure-to-flow rate relationship. This means that the constant observation and correction of flow rate through pressure is essential for accurate microscale printing.
Direct-Ink-Writing demonstration. Video obtained from WSU
Controlling the flow of compressible fluids, especially on the microscale, has proven to be a difficult challenge in the world of additive manufacturing. With the assistance of microfluidic sensors and mechatronic integration, a new level of accuracy and repeatability in a manageable timeframe is now feasible. This will pave a path for enhanced micro-printing with DIW through reactive in situ monitoring of pressure and flow rate, which also has promise for defect detection.
If you want to learn more about this work we invite you to visit Washington State University, School of Mechanical and Materials Engineering.
This work was financially supported by the National Science Foundation (NSF) grant 1825872 and NSF Graduate Research Fellowship Award 1842493.
How can we help you?
Name*
Email*
Message
Newsletter subscription
We will answer within 24 hours
By filling in your info you accept that we use your data.
Do you want tips on how to best set up your microfluidic experiment? Do you need inspiration or a different angle to take on your specific problem? Well, we probably have an application note just for you, feel free to check them out!
Microfluidics is the science of handling small amounts of liquids, inside micrometer scale channels. Discover how to handle fluids for your microfluidic experiments.
Learn how to set up your development environment for Elveflow products with this comprehensive tutorial.
This user guide will show you how to run microfluidic colocalization studies of single molecule spectroscopy.
This application note explores the basic principle of pneumatic pumps and a flow controller based on the basic principle of pneumatic pumps, known as pressure driven flow control. It also demonstrates the applications of pressure driven flow control in a range of industrial & research fields.
Flow regulation is a compulsory operation in most of the microfluidics operations. In some applications such as 2D or 3D cell culture, flow regulation is essential since accurate micro-environmental parameters control is required. Elveflow do it’s best to make this operation as easy as possible to help you to focus on what really matter in your setup.
Study the impact of molecular transport on cell cultures with a cross flow membrane chip and microfluidic instruments.
Precise liquid injection system for manipulation of small volumes of fluids using the MUX distribution and the MUX recirculation valve.
This application note explains how to set up a robust and reproducible microfluidic platform for liposomes assembly with improved encapsulation efficiency and reduced polydispersity in size.
Single-wall carbon nanotubes (SWCNTs) are considered as quasi 1-dimensional (1D) carbon nanostructures, which are known for their outstanding anisotropic electronic, mechanical, thermal and optical properties.
This application note describes how to combine and synchronise liquid perfusion and imaging using an Olympus spinning disc confocal microscope together with an Elveflow pressure-driven flow controlled microfluidic system.
Mixing is a crucial step for several microfluidic applications like chemical synthesis, clinical diagnostics, sequencing and synthesis of nucleic acids
This application note describes how microfluidic can be employed as a nanoparticle generator based on the example of PLGA bead generation.
Learn how to perform PLGA nanoparticle preparation with Elveflow instruments and a microfluidic chip
The application note describes how to convert various units of shear stress and/or pressure from one to another: shear stress conversion from Pascal, atmosphere, and N/m²...!
Get a quote
Collaborations
Need customer support?
Serial Number of your product
Support Type AdviceHardware SupportSoftware Support
Subject*
I hereby agree that Elveflow uses my personal data Newsletter subscription
Message I hereby agree that Elveflow uses my personal data Newsletter subscription